PT2262 PDF

DESCRIPTION. PT is a remote control encoder paired with PT utilizing CMOS Technology. It encodes data and address pins into a serial coded. PT Datasheet, PT Remote Control Encoder Datasheet, buy PT Remote Control Encoder. A6/D5 ~ A11/D0. I. Code Address Pin Nos.6 ~ 11/Data Pin Nos.5 ~ 0. These six tri -state pins are detected by PT to determine the encoded waveform bit 6.

Author: Vigul Shasar
Country: Germany
Language: English (Spanish)
Genre: Literature
Published (Last): 19 September 2004
Pages: 321
PDF File Size: 9.31 Mb
ePub File Size: 1.46 Mb
ISBN: 757-4-48911-319-1
Downloads: 12760
Price: Free* [*Free Regsitration Required]
Uploader: Gronris

Can I use more than one receiver? When purchasing these modules please ensure that match the correct frequency for your Tx and Rx pair and that the operating frequency is legal in your country.

There is one caveat that you can only pull one pin high at any one time. The pins on the receiver will mimic the state of the pins on the transmitter. Even with only 1 channel tried all 4 separately connected on the TX all 4 channels on the RX change Hi to Lo when the switch is changed. I can update the diagram tomorrow if you need to know how to do this. I made the resistors pullups so that the relays on our 4 channel relay module would be normally de-energised, forgetting how these module work!

I read that output type was momentary, and i need the remote circuit to mimic what happens at the tx switch end. Only if you can control when a PT transmits so that no two PT modules transmit at the same time. Board index Delete all board cookies Contact us. All posts 1 day 7 days 2 weeks 1 month 3 months 6 months 1 year Sort by: Can you switch the resistors and the switches around so that the resistors are pull-downs and the push buttons pull the pin up to 5V?

Related Articles  UP7706U8 EBOOK

Can I use more than one transmitter on different addresses? Edit That was it, swopped the connections round and its working correctly.

Please note that we currently stock two versions of these modules operating at or MHz. I’ll get the diagram updated as soon a possible.

PT2262 DIP-18 PTC Remote Control Encoder GEN23

You cannot have more than one PT module transmitting at the same time as they will interfere with each other, even if they are on different addresses. What does the DO do on the sensor? Author Post time Subject Direction: I bought 2 RX units and both do the same, but only 1 TX as that was all stock you had so not able to substitute that one.

On the transmitter module you can then connect a relay to drive your pump to the corresponding output pin D0, D1, D2 or D3. This makes them ideal for applications such as security systems, garage door controllers, home automation, and remote control.

PT & PT Wireless Modules (HCMODU & HCMODU) –

Yes, you can use as many receivers with one transmitter as you like. There are 4 pins on the transmitter and 4 pins on the receiver.


We cannot guarantee compatibility with other third party products. Will these modules do this? Ph2262 the address configurable on these modules?

The are intended as a simple way to remotely trigger something such as a garage door.

How do these modules work? They provide an easy way of remotely controlling up to 4 channels without the need of a microcontroller. Yes you can change the address, there are a set of pads on the underside of the modules that allow you to easily jumper with solder the appropriate pins to VCC or VDD. No, you can only send DC logic levels with these modules. For the UK please choose the MHz version.

Can I send serial data with these modules? It will then go back low when the button is released or the signal is interrupted in some way such as interference or going out of range. You do not have the required permissions to view the files attached to this post. Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.

DC 5V Working Current: This works as expected so I know the RX circuit is wired correctly.